GOMACO World Index
GOMACO World 28.3 - December 2000

University Corner: 2001 GOMACO University Class Schedule

GT-3600/Network Controller:

January 8-12, January 15-19, March 12-16, March 19-23, March 26-30 at the University. Four-day course covering the controls, setup adjustments, correct operating procedures, maintenance and troubleshooting for the GT-3600. Primary emphasis will be placed on the Network control system. Included in the operation section will be sessions on the setup of curb and gutter and barrier wall.

 

Commander III Three-Track/Network Controller:

January 22-26, January 29-February 2, April 2-6, April 9-13 at the University. Four-day course covering the controls, setup adjustments, correct operating procedures, maintenance and troubleshooting for the three-track Commander III. Primary emphasis will be placed on the Network control system. Included in the operation section will be sessions on the setup of curb and gutter, sidewalk and barrier wall.

 

New Generation Commander III/ Commander III Four-Track Network Controller:

February 5-9, February 12-16 at the University. Four-day course covering the controls, setup adjustments, correct operating procedures, maintenance and troubleshooting for the new generation Commander III four-track and the Commander III four-track. Four-track paving and barrier operations will be covered.

 

New Generation Commander III:

February 19-23, February 26-March 2 at the University. Four-day course covering the controls, setup adjustments, correct operating procedures, maintenance and troubleshooting for the new generation Commander III. Included in the operation section will be sessions on the setup of curb and gutter and barrier wall.

 

Commander II:

January 9-12 at the Paving Center. (Class begins on Tuesday.) Three-day course with primary emphasis on the Network control system of the Commander II. Setup procedures will be covered as well as machine maintenance. Troubleshooting of the hydraulic systems as well as the Network electrical circuits will conclude the week.

 

 

GT-3200:

January 16-19, January 23-26 at the Paving Center. (Class begins on Tuesday.) Three-day course covering the controls, setup adjustments and correct operating procedures for the GT-3200. Sessions on the setup of curb and gutter, maintenance and troubleshooting will be covered.

 

Trimmers Network Controller:

January 29-February 2, February 5-9, February 12-16 at the Paving Center. Four-day course covering the setup and operation of the 9000 and 9500 for trimming operations and concrete placing operations. Primary emphasis will be placed on the Network control system. Sessions on machine maintenance and troubleshooting will also be covered.

 

Two-Track Pavers:

February 19-23, February 26-March 2, March 5-9, March 12-16, April 2-6 at the Paving Center. Four-day course covering the proper setup and operation of two-track pavers. Primary emphasis will be placed on the GP-2600, GHP-2800 and the GP-4000. Machine maintenance and troubleshooting of the various hydraulic systems and electrical circuits will round out the week.

 

Four-Track Pavers:

March 19-23, March 26-30 at the Paving Center. Four-day course covering the proper setup and operation of four-track pavers. Primary emphasis will be placed on the GP-2600, GHP-2800 and the GP-4000. Machine maintenance and troubleshooting of the various hydraulic systems and electrical circuits will round out the week.

 

C-450:

April 10-13 at the Paving Center. (Class begins on Tuesday.) Three-day course covering the proper setup and operation of the C-450. Machine maintenance and troubleshooting of the various hydraulic systems and electrical circuits will round out the week.

 

 

 

GOMACO University is located at 321 First Street and GOMACO University Paving Center is located at 500 First Street, both in downtown Ida Grove, Iowa.

For further information, write:

GOMACO Training Department, GOMACO Corporation, PO Box 151, Ida Grove, Iowa 51445-0151 or Phone: 1-800-831-2320 or 712-364-3347, Fax: 712.364.4359 or e-mail: gomacou@gomaco.com. Students can also register for classes online or print out forms at http://www.gomaco.com/Resources/university/gomacouhome.html.

 

 

GOMACO World Index

Continue Reading GOMACO World Vol. 28, No. 3

 

 


GOMACO Home / Curb & Gutter / Pavers / Placer/Spreaders / Trimmer/Placers / Texture/Cure Machines / Cylinder Finishers / Canal/Slope / Airports / Support Equipment / Contact Us! / Sitemap / GOMACO University / Gomaco Trolley Company / Godbersen Equipment Company

Copyright © 1998-2017 GOMACO Corporation Inc.
All Rights Reserved
web@gomaco.com or visit our feedback page